Defender Security 812BF Especificaciones Pagina 18
- Pagina / 78
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
OPERATING INSTRUCTIONS
17
BEFORE USING THE CHIPPER (ALL MODELS)
IT IS ESSENTIAL TO CARRY OUT THE FOLLOWING TESTS to check safety fuctions - this
sequence of tests will only take a few seconds to carry out. We recommend that these tests are
carried out daily. Observing the function as described will confirm that the safety circuits are working
correctly. This is also a good opportunity to remind all operators of the control and emergency stop
systems.
3
6
4
5
7
1
2
PRESS THE GREEN
BUTTON
THE ROLLERS
SHOULD TURN FORWARDS
PRESS THE RED
SAFETY BAR
THE ROLLERS
SHOULD STOP
PRESS THE BLUE BUTTON
THE ROLLERS SHOULD TURN
BACKWARDS ONLY WHILE THE
BUTTON IS PRESSED
PRESS THE GREEN
BUTTON AGAIN
THE ROLLERS SHOULD
TURN FORWARDS
PRESS THE EMERGENCY
RED BUTTON
THE ROLLERS
SHOULD STOP
PRESS THE BLUE
BUTTON
THE ROLLERS
SHOULD NOT TURN
PULL TO RESET
THE RED BUTTON
THE MACHINE IS
READY TO USE
WITH THE ENGINE RUNNING AT FULL SPEED
STARTING TO CHIP (ALL MODELS)
WARNING
Do not use or attempt to start the chipper without the protective
guarding and discharge unit securely in place. Failure to do so may
result in personal injury or loss of life.
!
!
CHECK that chipper is running smoothly.
RELEASE catches on the feed tray and lower. Pull to release the red emergency stop button if
necessary.
PRESS green control button. The rollers will commence turning.
STAND to one side of the feed funnel.
PROCEED to feed material into the feed funnel.
CHIPPING (ALL MODELS)
Wood up to 190 mm diameter can be fed into the feed funnel. Put the butt end in first and engage it
with the feed rollers. The hydraulic feed rollers will pull the branch into the machine quite quickly.
Large diameter material will have its feed rate automatically controlled by the engine management
unit.
Sometimes a piece of wood that is a particularly awkward shape is too strong for the feed rollers to
break. This will cause the top roller to either bounce up and down on the wood or both rollers to stall.
If this occurs press the BLUE REVERSE button until the material has been released. Pull the material
out of the feed funnel and trim it so the chipper can process it.
Both feed rollers should always turn at the same speed. If one or both rollers stop or suddenly slow
down it may be that a piece of wood has become stuck behind one of the rollers. If this occurs press
the BLUE REVERSE button and hold for 2 seconds - then repress GREEN FEED button. This should
enable the rollers to free the offending piece of material and continue rotation at the correct speed. If
the rollers continue to stall in the 'forward feed' or 'reverse feed' position push the RED STOP
BUTTON, turn engine off, remove ignition key and investigate.
&
- CONTENTS 1
- TIMBERWOLF 190 CHIPPERS 2
- DIMENSIONS 3
- TW 190 ROAD TOW PARTS LOCATOR 4
- TW 190 TRACKED MODELS 6
- TW 190 TRACKED PARTS LOCATOR 7
- SAFE WORKING 10
- OPERATING INSTRUCTIONS 12
- STARTING TO CHIP (ALL MODELS) 18
- CHIPPING (ALL MODELS) 18
- SERVICE INSTRUCTIONS 20
- (TRACKED ONLY) 30
- WARRANTY (ALL MODELS) 33
- CERTIFICATE OF CONFORMITY 34
- IDENTIFICATION PLATES 35
- TIMBERWOLF 36
- Model shown 190DH 38
- ELECTRICAL DETAIL - 190TVGTR 39
- HYDRAULIC LAYOUT - 190TDHB 40
- HYDRAULIC LAYOUT - 190TFTR 41
- HYDRAULIC LAYOUT - 190TVGTR 42
- CIRCUIT DIAGRAM -190DHB/TFTR 43
- CIRCUIT DIAGRAM - 190TVGTR 44
- PARTS LISTS 45
- CHASSIS - 190TDHB 46
- CHASSIS - 190TFTR 47
- CHASSIS - 190TVGTR 48
- TILT MECHANISM (UPPER) 49
- CONTROL BOX- 190TDHB/TFTR 51
- CONTROL BOX- 190TVGTR 52
- CONTROL PANEL (ALL MODELS) 53
- DISCHARGE (ALL MODELS) 56
- DRIVE TRAIN - 190TDHB/TFTR 57
- DRIVE TRAIN - 190TVGTR 58
- ELECTRICAL LAYOUT - 190TVGTR 60
- ENGINE 190TDHB/TVGTR 61
- ENGINE - TW 190TFTR 62
- ENGINE BAY - 190TDHB 63
- ENGINE BAY - 190TFTR/TVGTR 64
- FUEL TANK (ALL MODELS) 65
- FUNNEL - 190TDHB/TFTR 66
- FUNNEL - 190TVGTR 67
- HYDRAULICS - 190TDHB 68
- HYDRAULICS - 190TFTR (1) 69
- HYDRAULICS - 190TFTR (2) 70
- HYDRAULICS - 190TFTR (3) 71
- HYDRAULICS - 190TVGTR (1) 72
- HYDRAULICS - 190TVGTR (2) 73
- HYDRAULICS - 190TVGTR (3) 74
- ROLLER BOX (ALL MODELS) 75
- ROTOR (ALL MODELS) 76
- ROTOR HOUSING (ALL MODELS) 77
- V-BELT TENSIONING TABLE 78
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Defender Security 812BF
(15 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales